標題: 利用高壓貫注環氧樹脂增加受高溫後之混凝土強度
Increase the Strength of Concrete Exposed Elevated Temperatures by High Pressure Injection Epoxy
作者: 鄭復平
CHENG FU-PING
國立交通大學土木工程學系(所)
關鍵字: 混凝土抗壓強度;火害:環氧樹脂貫注;強度恢復;Compressive Strength of Concrete;Fire Exposed;injection of epoxy;StrengthRecovery
公開日期: 2008
摘要: 混凝土受到高溫時,會有裂縫的產生,漿體也會產生分解,混凝土強度大幅度降低。目前業界處 理裂縫的作法。大都是使用打針貫注環氧樹脂的方法。如用水加以養護,混凝土會有再水化的現象, 可以揮復部份原有強度。於是合併上述兩種作法,利用含水份較多之高滲透性環氧樹脂以高壓方式貫 注受火害試體,以恢復受火害試體之抗壓強度。 影響混凝土強度最大的因子是火害溫度的高低,因此本計畫對於溫度的變數將採取 400oC 、 500oC 、600oC 、700oC 及800oC 五種溫度進行試驗。混凝土強度受火害影響的變數除了火害溫度以 外,冷卻速率的影響也非常大,本計畫將執行急速降溫及慢速降溫兩種方式。混凝土受火害後,其強 度仍然會持續的降低,其開始恢復強度的時間點會因所受火害溫度、再養護方法及冷卻方式有所不 同,因此開始進行環氧樹脂貫注的時間點也有可能影響補強的成效,本計畫對環氧樹脂貫注的時間點 設定為7 天、14 天及21 天三個變數。 本計畫之試體規畫為10 公分直徑20 公分長的圓柱試體,試驗強度為目前最為廣泛使用的 280 kgf / cm2,由於要作為比較使用,必須有參考樣品,因此必須有未受火害參考組、環氧樹脂貫注 前的參考組及在貫注環氧樹脂後28 天的試驗組等三組試體,每一組使用三個試體之平均。
When concrete exposed elevated temperature,decomposition of cement and cracks occur in concrete induce the decrease at strength of concrete. The injection of epoxy was used in industry to treat the problem of cracks. The re-curing by water can make concrete re-hydration and re-gain part of the strength due to exposed to fire. Using high pressure to inject epoxy which contain more water into concrete will work to recover the strength. Major parameter to affect the strength lost of concrete at elevated temperature is the temperature which concrete exposed. The parameter of temperatures used in this project are 400oC 、500oC 、600oC 、 700oC and 800oC . The cooling rate of concrete after exposing high temperature is important too. In this research both slow and rapid cooling rate will be adopted. Concrete continue to decrease its strength before recovering its strength by re-curing. The time begin to recover its strength depending on cooling rate, temperature exposed and re-curing approach. The Time to inject epoxy will scheduled to be 7 days, 14 days and 21 days. 10 cm diameter and 20 cm high concrete cylinder with compressive strength 280 kgf / cm2 will used in the test. The compressive strength before exposing high temperature will be used for reference. The compressive strength test will be executed for before and after the injection of epoxy. The average of three specimens will be used for each data,
官方說明文件#: NSC97-2221-E009-078
URI: http://hdl.handle.net/11536/102737
https://www.grb.gov.tw/search/planDetail?id=1688414&docId=291168
Appears in Collections:Research Plans


Files in This Item:

  1. 972221E009078.PDF